SMX9G16-13 Module Servo Drive

This product page covers SMB9G16-13 and SMC9G16-13 models (the X in SMX9G16-13 is a variable placeholder). SMB models use bus power logic. SMC models require an external 24 VDC logic power supply.

The SMX9G16-13 Gamma Series Digital PWM Servo Drive in the Module package configuration operates from 60-190 VDC and can output up to 10 A of continuous current.

All SMX9G16 models feature a current loop bandwidth of up to 5 kHz. Versions of SMX9G16 Gamma Series drives are available as UL Recognized Components for the USA and Canada, and can control brushless (standard servo and high-speed spindle), brush type, rotary, linear, voice coil, and AC induction motors. They also offer expanded command and control modes, including CANopen and indexing/point-to-point. Feedback is accepted from a wider range of devices and protocols, namely absolute serial encoders (BiSS, EnDat, and T-Format) and analog Sin/Cos encoders.

Command/Control Modes
+/-10 VDC for current (torque) or velocity (RPM)
Pulse (step) and direction
Encoder follower
CW/CCW (up/down mode)
External sine commutation (2-phase current mode)
RS-232 & RS-485
PWM for current (torque) or velocity (RPM) in 50% duty cycle format (one-wire) or 100% duty cycle format (two-wire)
Indexer/Point-to-Point
Camming/Gearing
CANopen
Feedback
Incremental quadrature encoder
Digital Hall sensors or commutation tracks from encoder
Absolute serial encoder (Biss, EnDat, and T-Format)
Analog Sin/Cos encoder
Resolver
Analog tachometer
I/O
Dedicated Digital Inputs: 2 STO optically isolated
Dedicated Digital Output: Brake (max 2 A @ 24 VDC)
Programmable Digital Inputs: 5 optically isolated, 6 Schmitt trigger, 2 differential
Programmable Digital Outputs: 3 MOSFETS (max 1.5A, 24 VDC), 2 optically isolated (max 10 mA, 24 VDC), relay (max 2 A, 30 VDC)
Analog Inputs: 2 differential (16 bit A/D)
Analog Outputs: 2 single ended, programmable (12 bit A/D)
Regulatory
Versions that are UL Recognized Components for the US and Canada are available.
Safety Disable
Safe Torque Off (STO) in accordance with IEC61800-5-2 (available upon request only)
Environmental Conditions
Storage Temperature: -40°C to 80°C
Standard Operating Temperature: refer to catalog, manual, or datasheet
Special Operating Temperature: refer to catalog, manual, or datasheet
Humidity: 5% to 95% relative humidity, non-condensing
Altitude: Up to 1000m without derating, derate current 10% per 1000m above 1000m
Performance
FOC All Gamma Series employ Field Oriented Control method which allows accurate control in both steady state or transient operation, and optimal orientation of the magnetic field.
Space Vector Modulation Glentek's advanced algorithms allow for maximum utilization of the DC bus voltage while generating minimum harmonic distortion of the currents in the winding of 3-phase AC motor.
Digital Current Loops Current loop bandwidths up to 5 kHz.
Digitally Tuned All parameters set digitally. No potentiometers to adjust. DSP control for the ultimate in high performance.
Parametric Filtering Provides control engineers advanced filtering to eliminate unwanted system mechanical resonance.
Smart-Comm Initialization Eliminates the need for Hall sensor or commutation tracks for many applications.
Auto Phase Advance Plug and Play for all types of three phase brushless motors. Provides control engineers the ability to connect any motor to the drive's motor outputs. The drives smart algorithm will automatically find and align the motor phases to allow for the most optimized smoothness and efficient commutation.
Sinusoidal Commutation For the ultimate in efficiency and smooth motion, commutates from almost any resolution linear, rotary encoder, or Hall sensors only.
Fault protection Short from output to output, short from output to ground, drive RMS over current, drive under/over voltage, drive over temperature, motor over temperature.
On-the-fly mode switching This feature allows the drive to switch between any mode of operation on-the-fly. That is, the drive can switch between current to velocity (or velocity to current), current to position (or position to current), and velocity to position (or position to velocity) while the motor is in motion. This feature is available upon request. Please contact Glentek application engineers for assistance.
Software configurable Glentek’s Windows based MotionMaestro software provides ease of set-up, monitoring and tuning with no previous programming experience required. This software is Windows 7, 8, and 10 compatible.
Silent operation 25 kHz PWM standard.
Command/Control Modes CANopen, +/-10V for current (torque) or velocity (RPM), pulse (step) and direction, encoder follower, external sine commutation (2-phase current mode), RS-232, RS-485, PWM for current (torque or velocity (RPM), and camming/gearing.
Regulatory
UL Recognized Versions that are UL Recognized Components for the US and Canada are available.
CE Marked All servo drives are CE marked.
RoHS Compliant RoHS compliance optional.
Connectivity
RS-232 or RS-485 High speed (115.2K baud) serial communication interface for setup and tuning and diagnostics.Note: RS-485 is optional.
CANopen High-speed (up to 1 Mbits/s) CAN interface for communications between nodes in real-time control applications. The drive device profile is based on IEC 61800-7-301/201 (CiA 402).
Feedback
Encoder feedback Accepts quadrature encoder signals up to 5 MHz (maximum frequency of up to 10 MHz is possible, but is system dependent). Absolute serial encoder (Biss, EnDat, and T-Format). Analog Sin/Cos encoder.
Encoder Output Divider The encoder input signal can be divided by a user selectable integer for the encoder output signal. Note: Available upon request only.
Resolver feedback For resolver feedback the drive creates a simulated encoder output with a typical resolution of 12 bits.
Tachometer feedback Accepts analog signals from all types of tachometer feedback.
I/O
Dedicated I/O Analog signal command, +/- limits, inhibit/enable, fault, reset, motor temp, encoder and step & direction. Programmable analog out: 2 12-bit. General purpose relay: maximum 2 amps @ 30 VDC. Nais P/N: TQSA-5V.
Build
Complete isolation Complete isolation between signal and power stage.
Non-volatile memory All parameters are stored in non-volatile memory for reliable start up. In addition, up to four different configurations can be stored in the drive's non-volatile memory.
Relay outputs Two pins provide an interface for the relay. They turn on when a desired condition occurs.
Status indicator 7-segment display indicates drive status and diagnostics.
SMT construction Provides ultra compact size, cost competitive package and high reliability.

9G16-lowpmodule-Model-1.png